H3C WX3024H无线AC配置方法
AC控制器配置:
在L3 switch上开启DHCP server功能,AP、无线客户端Client和有线客户端Host都能通过DHCP server自动获取IP地址 。
在L3 switch和AC上配置到达对端网段的静态路由 。
在AC上配置无线服务 , 确保Client可以通过配置的无线服务接入网络 。
配置注意事项
配置AP的序列号时请确保该序列号与AP唯一对应,AP的序列号可以通过AP设备背面的标签获取 。
配置L3 switch和AP相连的接口禁止VLAN 1报文通过,以防止VLAN 1内报文过多 。
1 配置AC
(1) 配置AC的接口
# 创建VLAN 10及其对应的VLAN接口 , 并为该接口配置IP地址 。AP将获取该IP地址与AC建立CAPWAP隧道 。
<AC> system-view
[AC] vlan 10
[AC-vlan10] quit
[AC] interface vlan-interface10
[AC-Vlan-interface10] ip address 10.152.1.6 255.255.255.0
[AC-Vlan-interface10] quit
# 创建VLAN 70,AC需要使用该VLAN转发无线客户端数据报文 。
[AC] vlan 70
[AC-vlan70] quit
# 配置AC和L3 switch相连的接口GigabitEthernet1/0/1为Trunk类型,禁止VLAN 1报文通过,允许VLAN 10和VLAN 70通过 。
[AC] interface gigabitethernet 1/0/1
[AC-GigabitEthernet1/0/1] port link-type trunk
[AC-GigabitEthernet1/0/1] undo port trunk permit vlan 1
[AC-GigabitEthernet1/0/1] port trunk permit vlan 10 70
[AC-GigabitEthernet1/0/1] quit
(2)配置三层路由
# 配置AC到10.152.7.0网段的静态路由,指定下一跳的IP地址为10.152.1.2 。
[AC] ip route-static 10.152.7.0.0 24 10.152.1.2
(3)配置无线服务
# 创建无线服务模板1,并进入无线服务模板视图 。
[AC] wlan service-template 1
# 配置SSID为Somidezoffice 。
[AC-wlan-st-1] ssid Somidezoffice
# 使能服务模板 。
[AC-wlan-st-1] service-template enable
[AC-wlan-st-1] quit
(4)配置AP
# 创建手工AP1,名称为officeap1(增加一个ap,增加一个名字),型号名称为WA4320i-ACN 。
[AC] wlan ap officeap1 model WA4320i-ACN
# 设置AP的序列号为210235A1GPC177000751 。
[AC-wlan-ap-officeap1] serial-id 210235A1GPC177000751
# 创建手工AP2
[AC] wlan ap officeap2 model WA4320i-ACN
[AC-wlan-ap-officeap2] serial-id 210235A1GPC179001703
以此类推....
# 进入AP的Radio 1视图 , 并将无线服务模板1绑定到Radio 1(5GHz)上,并指定客户端上线的VLAN为VLAN 70 。
[AC-wlan-ap-officeap1] radio 1
[AC-wlan-ap-officeap1-radio-1] service-template 1 vlan 70
# 开启Radio 1的射频功能 。
[AC-wlan-ap-officeap1-radio-1] radio enable
[AC-wlan-ap-officeap1-radio-1] return
# 进入AP的Radio 2视图,并将无线服务模板1绑定到Radio 2(2.4GHz)上,并指定客户端上线的VLAN为VLAN 70 。
[AC-wlan-ap-officeap1] radio 2
[AC-wlan-ap-officeap1-radio-2] service-template 1 vlan 70
# 开启Radio 1的射频功能 。
[AC-wlan-ap-officeap1-radio-2] radio enable
[AC-wlan-ap-officeap1-radio-2] return
【h3c无线ap设置方法图解 - 经验总结 www.jingyanzongjie.com】
以此类推.....
# 开启mac白名单,只允许白名单内客户端通过密码认证
[H3C]wlan whitelist mac xxxx-xxxx-xxxx
AC配置命令:
sysname H3C
#
vlan 10
#
vlan 70
#
wlan service-template 1
ssid somidezoffice
service-template enable
#
#
interface Vlan-interface10
ip address 10.152.1.6 255.255.255.0
#
interface Vlan-interface70
#
interface GigabitEthernet1/0/2
port link-mode bridge
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 10 70
#
line vty 0 4
authentication-mode scheme
user-role network-admin
protocol inbound ssh
#
ip route-static 10.152.7.0 24 10.152.1.2
#
snmp-agent
snmp-agent local-engineid 800063A28080F62E5885C000000001
snmp-agent community read somidez
snmp-agent sys-info version v2c v3
#
ssh server enable
#
local-user admin class manage
password simple Somidez_2018
service-type ssh https
authorization-attribute user-role network-admin
#
ip https enable
#
wlan ap 74ea-cbb4-7ac0 model WA4320i-ACN
serial-id 210235A1GPC177000751
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8114080 model WA4320i-ACN
serial-id 210235A1GPC179001703
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8114200 model WA4320i-ACN
serial-id 210235A1GPC179001715
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8116340 model WA4320i-ACN
serial-id 210235A1GPC179001981
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8117740 model WA4320i-ACN
serial-id 210235A1GPC179002141
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8114c60 model WA4320i-ACN
serial-id 210235A1GPC179001798
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac8114e80 model WA4320i-ACN
serial-id 210235A1GPC179001815
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eac81162c0 model WA4320i-ACN
serial-id 210235A1GPC179001977
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan ap 74eacbb47ac0 model WA4320i-ACN
serial-id 210235A1GPC179000751
radio 1
radio enable
service-template 1 vlan 70
radio 2
radio enable
service-template 1 vlan 70
#
wlan whitelist mac-address 3052-cb02-27ec
wlan whitelist mac-address d0fc-cc37-1604
三层交换机配置命令:
(1) 配置L3 switch的接口
# 创建VLAN 70和VLAN 10,并配置IP地址,用于转发AC和AP间的CAPWAP隧道内的流量 。
<L3 switch> system-view
[L3 switch] vlan 10
[L3 switch-vlan10] quit
[L3 switch] interface vlan-interface 10
[L3 switch-Vlan-interface10] ip address 10.152.1.2 255.255.255.0
[L3 switch-Vlan-interface10] quit
[L3 switch] vlan 70
[L3 switch-vlan70] quit
[L3 switch] interface vlan-interface 70
[L3 switch-Vlan-interface70] ip address 10.152.7.1 255.255.255.0
[L3 switch-Vlan-interface70] quit
# 配置L3 switch和AC相连的接口GigabitEthernet1/0/1为Trunk类型,允许VLAN10和VLAN 70通过 。
[L3 switch] interface gigabitEthernet 1/0/1
[L3 switch-GigabitEthernet1/0/1] port link-type trunk
[L3 switch-GigabitEthernet1/0/1] port trunk permit vlan 10 70
[L3 switch-GigabitEthernet1/0/1] quit
# 配置L3 switch和AP相连的接口GigabitEthernet1/0/2为Trunk类型,允许所有VLAN通过 , 当前Trunk口的PVID为70 。
[L3 switch] interfac gigabitEthernet 1/0/2
[L3 switch-GigabitEthernet1/0/2] port link-type trunk
[L3 switch-GigabitEthernet1/0/2] port trunk permit vlan all
[L3 switch-GigabitEthernet1/0/2] port trunk pvid vlan 70
[L3 switch-GigabitEthernet1/0/2] quit
(2)配置DHCP server
# 开启DHCP server功能 。
[L3 switch] dhcp enable
# 配置DHCP地址池vlan70为AP分配地址范围为10.152.7.0/24 , 网关地址为10.152.7.1 。
[L3 switch] dhcp server ip-pool vlan70
[L3 switch-dhcp-pool-vlan70] network 10.152.7.0mask 255.255.255.0
[L3 switch-dhcp-pool-1] gateway-list 10.152.7.1
# 配置DHCP Option43的内容为AC的十六进制IP地址 。
[L3 switch-dhcp-pool-1] option 43 hex 80070000010a980106
[L3 switch-dhcp-pool-1] quit
继续AC控制器的界面话配置:
WiFi密码设置:
【网络】--【无线网络】--编辑该ssid
选择加密方式:
【无线配置】--【AP管理】
2.1、默认关闭2.4ghzWiFi,开启2.4ghzwifi,【网络】--【AP管理】--【AP】
2.2、AP全局配置固化,全部开启
2.3、AP预配置
2.3.1、开启自动下发功能